ISO 3310-1:2016(en) Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 24, Particle characterization including sieving, Subcommittee SC 8, Test sieves, sieving and industrial screens.
This fifth edition cancels and replaces the fourth edition (ISO 3310-1:2000), which has been technically revised. It also incorporates the Technical Corrigendum ISO 3310-1:2000/Cor 1:2004.
ISO 3310 consists of the following parts, under the general title Test sieves — Technical requirements and testing:
— Part 1: Test sieves of metal wire cloth
— Part 2: Test sieves of perforated metal plate
— Part 3: Test sieves of electroformed sheets
Introduction
As the accuracy of test sieving depends on the dimensional accuracy of the test sieve openings, it is considered necessary in this part of ISO 3310 to keep the maximum permissible error on the apertures in metal wire cloth as close as possible.
Requirements other than maximum permissible errors on the apertures, such as requirements for the wire diameter, have not been limited more closely than necessary, since the influence of these criteria on test sieving is of minor importance, and excessively strict requirements may make manufacturing unnecessarily difficult.
1 Scope
This part of ISO 3310 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth.
It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.
2 Normative references
The following referenced documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 565:1990, Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
ISO 2395, Test sieves and test sieving — Vocabulary
ISO 2591-1:1988, Test sieving — Part 1: Methods using test sieves of woven wire cloth and perforated metal plate
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2395 and the following apply.
3.1
test sieve
<particle size analysis> measuring instrument used for sieving
Note 1 to entry: ISO/IEC Guide 99:2007 defines a “measuring instrument” as a device used for making measurements, alone or in conjunction with one or more supplementary devices.
Made in China Mao Qun stainless steel wire mesh, stainless steel screen mesh, stainless steel woven mesh, nickel alloy wire mesh, copper wire mesh, screen mesh,GFW metal wire mesh,Stainless steel wire mesh,Alloy wire mesh,Knitted metal wire mesh,Woven Wire Mesh,Structured packing